最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

ISL5239KI Datasheet

  • ISL5239KI

  • Pre-Distortion Linearizer

  • 31頁

  • INTERSIL   INTERSIL

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

ISL5239
General Comments About Modes
Once a trigger is detected in the ARMED condition, all
following triggers are ignored during the sequence. The
system does not acknowledge new triggers until a new
transaction is invoked and re-armed. When a new mode is
invoked, all subsequent invocations of new modes during the
duration of its sequence is ignored, except in the loop mode.
In the loop mode, an input memory mode change to IDLE is
processed immediately.
When in the IDLE, all controls, addresses, and data, default
to the processor interface values.
into the memory. The I data is read from the memory on the
DataHigh register and the Q data, DataLow register.
In the predistort magnitude input, the data is unsigned 16
bits and the software has to reshuffle the data to extract the
original magnitude. The DataHigh contains only the pre-
distorter magnitude bit 15, and the DataLow contains the
pre-distorter magnitude 14:0.
Writing/Reading the Memories from the Processor
Interface
In the auto-increment mode, the data is loaded in 16-bit
increments. The low word is written or read first followed by
the high word. The high word increments the address
counter and generates the actual write to the memory. For
reading, it just increments the counter. The input memory
select 0x04, bit 12, selects the memory to be written to or
read from.
When writing or reading a specific address, the 0x0b
address register must be loaded before the 0x0c and 0x0d
memory data registers. In the write, the high word
transaction will trigger the actual write to the memory and a
low word must be written first. For additional details, see the
uP interface section.
Triggers
When a capture memory is ARMED, i.e. waiting for a trigger
to happen, the activation of the trigger occurs in three ways
鈥?external, data dependent, and user invoked. The trigger
select, 0x04, bits 5:4, provides the selection of the trigger
source. When the pre-distorter magnitude bus values fall
between the range of 0x09 minimum and 0x0a maximum,
the data dependent trigger activates. The first of these
transitions causes a trigger to be detected and the remaining
triggers during the capture sequence is ignored.
To invoke the user invoked trigger, 0x04, 5:4, set to
processor, the programmer writes a TRIGGER to the 0x04,
bit 6 processor trigger register. After a TRIGGER is in the
field, the user initiates the trigger by just writing to that
register. The user does not have to reset the trigger back to
IDLE. By setting the processor trigger bit to IDLE when not in
use, it keeps the circuit quiet and allows the user to write to
other values at that address without causing a trigger to
occur during operation. To disable the processor trigger, the
user should change trigger select to something other than
PROCESSOR and then change values in processor trigger.
If trigger select is not set to PROCESSOR, the system
ignores the trigger generated by processor trigger.
The feedback and input memory circuit uses the same
trigger; both circuits trigger at the same point with its
operation registers causing different operations to occur. The
user should monitor input memory status and feedback
memory status simultaneously before activating triggers.
Make sure both status registers are in ARMED before
activating triggers or the results from the capture can be
erroneous and data can be overwritten. Selecting processor
trigger (register 0x04, bits 5:4 = 00) while arming the input
and feedback memory circuits is a convenient way to ensure
no unexpected triggers occur before confirming ARMED
status of both circuits.
Microprocessor Interface
The microprocessor interface allows the ISL5239 to appear
as a memory mapped peripheral to the
碌P.
All registers can
be accessed through this interface. The interface consists of
a 16 bit bidirectional data bus, P<15:0>, six bit address bus,
A<5:0>, a write strobe (WR), a read strobe (RD) and a chip
enable (CE). The interface is configured for separate read
and write strobe inputs.
The processor interface provides a simple parallel
Data/Control/Address bus for monitoring and controlling its
operation. The processor interface is asynchronous to the
CLK, and BUSY signal is included to indicate when read and
write operations are complete.
The register configuration is master/slave, where the slave
registers are updated from the masters and all reads access
the slaves.
The master registers are clocked by the
碌P
WR strobe, are
writable and cleared by a hard reset. The slave registers are
clocked by CLK, and are readable and cleared by either a
hard or soft reset. The transfer of configuration data from the
master register to the slave register occurs synchronously
after an event and requires a four clock synchronization
period.
The
碌P
can perform back-to-back accesses to the register,
but must maintain four f
CLK
periods between accesses to
the same address. This limits the maximum
碌P
access rate
for the RAM to 125MHz/4 = 31.25MHz.
Input Data to Input Memory
There are three sources of input data to the input memory 鈥?/div>
interpolator, pre-distorter鈥檚 data outputs, and the pre-
distorter鈥檚 magnitude. Data from the interpolator and the
predistort output are the upper 16 bits with or without
rounding. Only 16 of the original 20 bits of I or Q is loaded
12

ISL5239KI 產品屬性

  • Intersil

  • 1.8 V

  • 300 mA

  • BGA

  • Tray

ISL5239KI相關型號PDF文件下載

  • 型號
    版本
    描述
    廠商
    下載
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL [...
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL [...
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL
  • 英文版
    Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches
    INTERSIL
  • 英文版
    Four-Channel Programmable Digital DownConverter
    INTERSIL
  • 英文版
    Quad Programmable Up Converter
    INTERSIL
  • 英文版
    Pre-Distortion Linearizer
    INTERSIL
  • 英文版
    CommLink Direct Digital Synthesizer
    Intersil
  • 英文版
    Four-Channel Wideband Programmable DownConverter
    INTERSIL
  • 英文版
    3.3V Ringing SLIC Family for Voice Over Broadband (VOB)
    INTERSIL
  • 英文版
    Low Power Ringing SLIC for Home Gateways
    INTERSIL
  • 英文版
    Dual 8-bit, +3.3V, 260+MSPS, High Speed D/A Converter
    intersil
  • 英文版
    Dual 8-bit, +3.3V, 130/210+MSPS, High Speed D/A Converter
    INTERSIL
  • 英文版
    3V Dual 8-Bit, 20/40/60MSPS A/D Converter with Internal Volt...
    Intersil
  • 英文版
    Dual 10-bit, +3.3V, 260+MSPS, High Speed D/A Converter
    intersil
  • 英文版
    Dual 10-bit, +3.3V, 130/210+MSPS, High Speed D/A Converter
    INTERSIL
  • 英文版
    3V Dual 10-Bit, 20/40/60MSPS A/D Converter with Internal Vol...
    Intersil
  • 英文版
    10-bit, +3.3V, 260+MSPS, High Speed D/A Converter
    INTERSIL

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！