最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

ISL5585 Datasheet

  • ISL5585

  • 3.3V Ringing SLIC Family for Voice Over Broadband (VOB)

  • 456.00KB

  • 24頁

  • INTERSIL   INTERSIL

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

ISL5585
High Battery Operation
Other than during ringing, the high battery should be used
for standby conditions which must provide MTU compliance.
During standby operation the power consumption is typically
85mW with -100V battery. If ringing requirements do not
require full 100V operation, then a lower battery will result in
lower standby power.
switch is designed to have a maximum on voltage of 0.6V
with a load current of 45mA.
+V
RELAY
SW+
SW-
SWC
High Voltage Decoupling
The 100V rating of the device will require a capacitor of
higher voltage rating for decoupling. Suggested decoupling
values for all device pins are 0.1碌F. Standard surface mount
ceramic capacitors are rated at 100V. For applications
driven at low cost and small size, the decoupling scheme
shown below could be implemented.
FIGURE 15. EXTERNAL RELAY SWITCHING
0.22碌
0.22碌
Since the device provides the ringing waveform, the relay
functions which may be supported include subscriber
disconnect, test access or line interface bypass. An external
snubber diode is not required when using the uncommitted
switch as a relay driver.
Test Load
VBL
VBH
ISL5585
FIGURE 14. ALTERNATE DECOUPLING SCHEME
The switch may be used to connect test loads across Tip
and Ring. The test loads can provide external test
termination for the device. Proper connection of the
uncommitted switch to Tip and Ring is shown below.
TIP
It is important to place the external diode between the VBH
pin and the decoupling capacitor. Attaching the decoupling
capacitor directly to the VBH pin will degrade the reliability of
the device. Refer to Figure 14 for the proper arrangement.
This applies to both single and stacked and decoupling
arrangements.
If VBL and VBH are tied together to override the battery
switch function, then the external diode is not needed and
the decoupling may be attached directly to VBH.
RING
TEST
LOAD
SW+
SW-
SWC
Uncommitted Switch
Overview
The uncommitted switch is a three terminal device designed
for flexibility. The independent logic control input, SWC,
allows switch operation regardless of device operating
mode. The switch is activated by a logic low. The positive
and negative terminals of the device are labeled SW+ and
SW- respectively.
FIGURE 16. TEST LOAD SWITCHING
The diode in series with the test load blocks current from
flowing through the uncommitted switch when the polarity of
the Tip and Ring terminals are reversed. In addition to the
reverse active state, the polarity of Tip and Ring are
reversed for half of the ringing cycle. With independent logic
control and the blocking diode, the uncommitted switch may
be continuously connected to the Tip and Ring terminals.
Relay Driver
The uncommitted switch may be used as a relay driver by
connecting SW+ to the relay coil and SW- to ground. The
19

ISL5585 PDF文件相關型號

ISL5585 XXX,ISL5585AIMZ,ISL5585BIMZ,ISL5585CIMZ,ISL5585DIMZ,ISL5585ECMZ,ISL5585ECRZ,ISL5585FCRZ,ISL5585GCMZ

ISL5585相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！