最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

LPC47M172_07 Datasheet

  • LPC47M172_07

  • SMSC Corporation [Advanced I/O Controller with Motherboard ...

  • 1113.49KB

  • SMSC   SMSC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

Advanced I/O Controller with Motherboard GLUE Logic
Datasheet
Table 6.23 - Verify Command Result Phase Table
MT
0
0
0
0
1
1
1
1
Note:
EC
0
0
1
1
0
0
1
1
SC/EOT VALUE
SC = DTL
EOT <= # Sectors Per Side
SC = DTL
EOT > # Sectors Per Side
SC <= # Sectors Remaining AND
EOT <= # Sectors Per Side
SC > # Sectors Remaining OR
EOT > # Sectors Per Side
SC = DTL
EOT <= # Sectors Per Side
SC = DTL
EOT > # Sectors Per Side
SC <= # Sectors Remaining AND
EOT <= # Sectors Per Side
SC > # Sectors Remaining OR
EOT > # Sectors Per Side
TERMINATION RESULT
Success Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
Successful Termination
Result Phase Valid
Unsuccessful Termination
Result Phase Invalid
If MT is set to 鈥?鈥?and the SC value is greater than the number of remaining formatted sectors on Side 0,
verifying will continue on Side 1 of the disk.
6.17
Format A Track
The Format command allows an entire track to be formatted. After a pulse from the nINDEX pin is
detected, the FDC starts writing data on the disk including gaps, address marks, ID fields, and data fields
per the IBM System 34 or 3740 format (MFM or FM respectively). The particular values that will be written
to the gap and data field are controlled by the values programmed into N, SC, GPL, and D which are
specified by the host during the command phase. The data field of the sector is filled with the data byte
specified by D. The ID field for each sector is supplied by the host; that is, four data bytes per sector are
needed by the FDC for C, H, R, and N (cylinder, head, sector number and sector size respectively).
After formatting each sector, the host must send new values for C, H, R and N to the FDC for the next
sector on the track. The R value (sector number) is the only value that must be changed by the host after
each sector is formatted. This allows the disk to be formatted with nonsequential sector addresses
(interleaving). This incrementing and formatting continues for the whole track until the FDC encounters a
pulse on the nINDEX pin again and it terminates the command.
Table 6.24 contains typical values for gap fields that are dependent upon the size of the sector and the
number of sectors on each track. Actual values can vary due to drive electronics.
SMSC/Non-SMSC Register Sets (Rev.
01-11-07)
Page 66
SMSC LPC47M172
DATASHEET

LPC47M172_07 PDF文件相關型號

LPC47M172-NW

LPC47M172_07相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！