最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

LPC47M172_07 Datasheet

  • LPC47M172_07

  • SMSC Corporation [Advanced I/O Controller with Motherboard ...

  • 1113.49KB

  • SMSC   SMSC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

Advanced I/O Controller with Motherboard GLUE Logic
Datasheet
6.11
Data Transfer Commands
All of the Read Data, Write Data and Verify type commands use the same parameter bytes and return the
same results information, the only difference being the coding of bits 0-4 in the first byte.
An implied seek will be executed if the feature was enabled by the Configure command. This seek is
completely transparent to the user. The Drive Busy bit for the drive will go active in the Main Status
Register during the seek portion of the command. If the seek portion fails, it is reflected in the results
status normally returned for a Read/Write Data command. Status Register 0 (ST0) would contain the error
code and C would contain the cylinder on which the seek failed.
6.11.1 Read Data
A set of nine (9) bytes is required to place the FDC in the Read Data Mode. After the Read Data
command has been issued, the FDC loads the head (if it is in the unloaded state), waits the specified head
settling time (defined in the Specify command), and begins reading ID Address Marks and ID fields. When
the sector address read off the diskette matches with the sector address specified in the command, the
FDC reads the sector鈥檚 data field and transfers the data to the FIFO.
After completion of the read operation from the current sector, the sector address is incremented by one
and the data from the next logical sector is read and output via the FIFO. This continuous read function is
called 鈥淢ulti-Sector Read Operation鈥? Upon receipt of the TC cycle, or an implied TC (FIFO
overrun/underrun), the FDC stops sending data but will continue to read data from the current sector,
check the CRC bytes, and at the end of the sector, terminate the Read Data Command.
N determines the number of bytes per sector (see Table 6.18 below). If N is set to zero, the sector size is
set to 128. The DTL value determines the number of bytes to be transferred. If DTL is less than 128, the
FDC transfers the specified number of bytes to the host. For reads, it continues to read the entire 128-
byte sector and checks for CRC errors. For writes, it completes the 128-byte sector by filling in zeros. If N
is not set to 00 Hex, DTL should be set to FF Hex and has no impact on the number of bytes transferred.
Table 6.18 - Sector Sizes
N
00
01
02
03
..
07
SECTOR SIZE
128 bytes
256 bytes
512 bytes
1024 bytes
鈥?/div>
16 Kbytes
The amount of data which can be handled with a single command to the FDC depends upon MT (multi-
track) and N (number of bytes/sector).
The Multi-Track function (MT) allows the FDC to read data from both sides of the diskette. For a particular
cylinder, data will be transferred starting at Sector 1, Side 0 and completing the last sector of the same
track at Side 1.
If the host terminates a read or write operation in the FDC, the ID information in the result phase is
dependent upon the state of the MT bit and EOT byte. Refer to Table 6.19.
SMSC/Non-SMSC Register Sets (Rev.
01-11-07)
Page 62
SMSC LPC47M172
DATASHEET

LPC47M172_07 PDF文件相關型號

LPC47M172-NW

LPC47M172_07相關型號PDF文件下載

  • 型號
    版本
    描述
    廠商
    下載
  • 英文版
    100 PIN ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE
    SMSC
  • 英文版
    100 PIN ENHANCED SUPER I/O CONTROLLER WITH LPC INTERF...
    SMSC [SMSC...
  • 英文版
    128 Pin Enhanced Super I/O with LPC Interface for Consumer A...
    SMSC
  • 英文版
    128 Pin Enhanced Super I/O with LPC Interface for Con...
    SMSC [SMSC...
  • 英文版
    100 Pin Enhanced Super I/O for LPC Bus with SMBus Controller...
    SMSC
  • 英文版
    100 Pin Enhanced Super I/O for LPC Bus with SMBus Con...
    SMSC [SMSC...
  • 英文版
    Microcontroller
    ETC
  • 英文版
    SMSC Corporation [100 Pin Enhanced Super I/O Controller wit...
    SMSC
  • 英文版
    ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE
    SMSC
  • 英文版
    ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE
    SMSC [SMSC...
  • 英文版
    LPC47M13x_SMSC Corporation.pdf
    SMSC Corporatio...
  • 英文版
    128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE ...
    SMSC
  • 英文版
    128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INT...
    SMSC [SMSC...
  • 英文版
    ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
    SMSC
  • 英文版
    ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
    SMSC [SMSC...
  • 英文版
    ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
    SMSC
  • 英文版
    ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
    SMSC [SMSC...
  • 英文版
    LPC SUPER I/O WITH HARDWARE MONITORING BLOCK
    SMSC
  • 英文版
    LPC SUPER I/O WITH HARDWARE MONITORING BLOCK
    SMSC [SMSC...
  • 英文版
    SMSC Corporation [LPC Super I/O IrDA Hot Docking Chip with ...
    SMSC

掃碼下載APP,
一鍵連接廣大的電子世界。

在線人工客服

買家服務:
賣家服務:
技術客服:

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號,
第一時間獲取資訊。

建議反饋

聯系人:

聯系方式:

按住滑塊,拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見,您的參與是維庫提升服務的動力!意見一經采納,將有感恩紅包奉上哦!