調過cxd3068 servo 進來聊一聊

作者：mary huang　欄目：數字廣電

調過CXD3068 servo 進來聊一聊
這段程試有問題嗎?
BYTE Servo_focus_on(void)
{

    SWITCH (servo.operation)
    {
        case SERVO_FOCUS_0:
            #ifdef SERVO_DEBUGON
                epp_write_wait("###Servo Focus On\n\r");
            #endif
            FoFail = 0;
            servo_wait_gfs_cnt = 0;
            servo.temp_counter = 0;
            SERVO_SPEED_SET;                    /* Set RF EQ for 1X play */
            Servo_send_data_latch(0x3bf050, 3); /*  Jerry:  0x3be020, 702:  0x3bf050 */
            servo.operation = SERVO_FOCUS_1;
            servo.operation_timer = SERVO_TIME_200MS;
            servo.timeout_timer = SERVO_FOCUS_ON_TIMEOUT;                /* Wait For Tuning */
            if(servo.focuson_fail_counter > 4)  // Flying Disc Protection
            {
                #ifdef ERROR_MSG
                    epp_write_wait("^^^^^Flying Disc Protection 2!\n\r");
                #endif
                SERVO_LDON_CLR;
                Servo_off();
                servo.operation_timer = 3000 * servo.focuson_fail_counter;
                servo.timeout_timer = servo.operation_timer + SERVO_FOCUS_ON_TIMEOUT;
            }
            break;
        case SERVO_FOCUS_1:
            if(servo.operation_timer)
                break;

            SERVO_LDON_SET;
            Servo_off();
            #ifdef FOCUSON_DEBUGON
                epp_write_wait("LD ON\n\r");
            #endif

            if(servo_low_level)
                Servo_send_data_latch(0x3748ba, 3);     /* Set FZC level VC/8 */
            else
                Servo_send_data_latch(0x3708ba, 3);     /* Set FZC level VC/4 */
            if(FoFail > 1)
            {
                servo.buf[3] = 0;
                Servo_send_data_latch(0xe00000, 3);         /* Spindle off */
                servo.operation_timer = 4000;   /* to Make time Out!!! and wait Disc Stop Spin */
                servo.timeout_timer = 500;  /* delay 500ms then response focus fail cmd to DSA */
                FoFail = 0;
            }
            else
            {
            Servo_send_data_latch(0xe80000, 3);         /* Spindle Forward Kick */
                if(servo_sledge_lba != 450000)
                {
                    servo.operation_timer = (350 - (servo_sledge_lba >> 16)*30);    /* Wait Disc Rotate */
                    #ifdef FOCUSON_DEBUGON
                        psprintf(linebuf,"Spd Acc time = %d(O)\n\r",servo.operation_timer);
                        epp_write_wait(linebuf);
                    #endif
                }
                else
                {
                    servo.operation_timer = 200;    /*  */
                    #ifdef FOCUSON_DEBUGON
                        epp_write_wait("Spd Acc time = 200(X)\n\r");
                    #endif

2樓：	>>參與討論
作者： liu701230 于 2005/9/21 10:20:00 發布：現在調好了嗎？朋友！，現在調好了嗎？

3樓：	>>參與討論
作者： mary huang 于 2005/9/21 18:03:00 發布：這段程試focus 很慢不知到,是光頭的原因,還是程試不行 * - 本貼最后修改時間：2005-9-21 18:08:06 修改者：mary huang

參與討論

相關帖子

顯卡有s-video信號，液晶電視只有AV輸入端口，如何連接？

尋：用蜂鳴片做傳感器的震動觸發電路

請教不認光驅故障？

MPEG-4的視頻壓縮率？

哪位給介紹一個LED的驅動芯片

免費注冊為維庫電子開發網會員，參與電子工程師社區討論，點此進入

最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

調過cxd3068 servo 進來聊一聊