最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

K4H1G0438M-TCA0 Datasheet

  • K4H1G0438M-TCA0

  • 128Mb DDR SDRAM

  • 669.26KB

  • 53頁

  • SAMSUNG   SAMSUNG

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

128Mb DDR SDRAM
3. For a Write with autoprecharge command, a new Bank Activate command may be issued to the same
bank after tWR+tRP where tWR+tRP starts on the falling DQS edge that strobed in the last valid data and
ends on the rising clock edge that strobes in the Bank Activate command. During write with
autoprecharge, the initiation of the internal precharge occurs at the same time as the earliest possible
external Precharge command without interrupting the Write burst as described in 1 above.
4. In all cases, a Precharge operation cannot be initiated unless tRAS(min) [minimum Bank Activate to
Precharge time] has been satisfied. This includes Write with autoprecharge commands where tRAS(min)
must still be satisfied such that a Write with autoprecharge command has the same timing as a Write
command followed by the earliest possible Precharge command which does not interrupt the burst.
5. Refer to "3.3.2 Burst write operation"
3.3.9 Burst Stop
The burst stop command is initiated by having RAS and CAS high with CS and WE low at the rising edge of
the clock(CK). The burst stop command has the fewest restrictions making it the easiest method to use when
terminating a burst read operation before it has been completed. When the burst stop command is issued dur-
ing a burst read cycle, the pair of data and DQS(Data Strobe) go to a high impedance state after a delay which
is equal to the CAS latency set in the mode register. The burst stop command, however, is not supported dur-
ing a write burst operation.
< Burst Length=4, CAS Latency= 2, 2.5 >
0
CK
CK
Command
DQS
CAS Latency=2
DQ
鈥瞫
DQS
CAS Latency=2.5
DQ
鈥瞫
Dout 0 Dout 1
Dout 0 Dout 1
The burst ends after a delay equal to the CAS latency.
READ A
Burst Stop
NOP
NOP
NOP
NOP
NOP
NOP
NOP
1
2
3
4
5
6
7
8
Figure 17. Burst stop timing
The Burst Stop command is a mandatory feature for DDR SDRAMs. The following functionality is required:
1. The BST command may only be issued on the rising edge of the input clock, CK.
2. BST is only a valid command during Read bursts.
3. BST during a Write burst is undefined and shall not be used.
4. BST applies to all burst lengths.
5. BST is an undefined command during Read with autoprecharge and shall not be used.
- 27 -
REV. 1.0 November. 2. 2000

K4H1G0438M-TCA0相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！