L497
PIN FUNCTIONS
(refer to fig. 4)
N
擄
1
2
3
Name
GND
SIGNAL GND
POWER SUPPLY
Function
This pin must be connected to ground.
This pin must be connected to ground.
Supply Voltage Input. An internal 7.5 V (typ) zener zener limits the voltage
at this pin. The external resistor R
5
limits the current through the zener for
high supply voltages.
This pin must be connected to ground or left open.
Hall-effect Pickup Signal Input. This input is dwell control circuit output in
order to enable the current driving into the coil. The spark occurs at the
high-to-low transition of the hall-effect pickup signal.
Furthermore this input signal enables the slow recovery and permanent
conduction protection circuits. The input signal, supplied by the open
collector output stage of the Hall effect sensor, has a duty-cycle typically
about 70 %. V
5
is internally clamped to V
3
and ground by diodes
Open collector output which is at a low level when current flows in the
ignition coil. For high voltages protection of this output, connection to the
pin 7 zener is recommended.
In this situation R
8
must limit the zener current, too, and R
1
limits pin 6
current if RPM module pad is accidentally connected to V
S
.
A 21 V (typ) General Purpose Zener. Its current must be limited by an
external resistor.
A capacitor connected between this pin and ground sets the slope of the
dwell time variation as it rises from zero to the correct value. This occurs
after the detection of I
coll
鈮?/div>
94 % I
nom
, just before the low transition of the
hall-effect signal pulse.
The duration of the slow recovery is given by :
t
src
= 12,9 R
7
C
src
(ms)
where R
7
is the biasing resistor at pin 12 (in K
鈩?/div>
) and C
src
is the delay
capacitor at pin 8 (in
碌
F).
A capacitor connected between this pin and ground determines the
intervention delay of the permanent conduction protection. After this delay
time the coil current is slowly reduced to zero.
Delay Time T
p
is given by :
T
p
=16 C
p
R
7
(ms)
where R
7
is the biasing resistor at pin 12 (in K鈩? and C
P
is the delay
capacitor at pin 9 (in
碌
F).
A capacitor C
T
connected between this pin and ground is charged when the
HAll effect output is High and is discharged at the High to Low transition of
the Hall effect signal.
The recommended value is 100 nF using a 62 K鈩?resistor at pin 12.
The average voltage on the capacitor CW connected between this pin and
ground depends on the motor speed and the voltage supply. The
comparison between V
CW
and V
CT
voltage determines the timing for the
dwell control. For the optimized operation of the device C
T
= C
W
; the
recommended value is 100 nF using a 62 K鈩?resistor at pin 12.
A resistor connected between this pin and ground sets the internal current
used to drive the external capacitors of the dwell control
(pin 10 and 11) permanent conduction protection (pin 9) and slow recovery
time (pin 8). The recommended value is 62 K
鈩?/div>
.
Connection for the Coil Current Limitation. The current is measured on the
sensing resitor R
S
and taken through the divider R
10
/R
11
. The current
limitation value is given by :
I
sens
=
0.32
鈰?/div>
R
10
+
R
11
R
S
鈰?/div>
R
11
3/11
4
5
N.C.
HALL-EFFECT INPUT
6
RPM OUTPUT
7
8
AUX. ZENER
RECOVERY TIME
9
MAX CONDUCTION
TIME
10
DWELL CONTROL
TIMER
11
DWELL CONTROL
12
BIAS CURRENT
13
CURRENT SENSING
L497相關(guān)型號PDF文件下載
-
型號
版本
描述
廠商
下載
-
英文版
HALL EFFECT PICKUP IGNITION CONTROLLER
-
英文版
HALL EFFECT PICKUP IGNITION CONTROLLER
STMICROELECTRON...
-
英文版
10A SWITCHING REGULATOR
-
英文版
10A SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
1.5A STEP DOWN SWITCHING REGULATOR
-
英文版
Buck Switching Regulator IC Positive Adjustable 3.3V 1 Outpu...
-
英文版
1.5A STEP DOWN SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
2A SWITCHINGREGULATOR
-
英文版
2A SWITCHINGREGULATOR
STMICROELECTRON...
-
英文版
3.5A STEP DOWN SWITCHING REGULATOR
-
英文版
3.5A STEP DOWN SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
3.5A SWITCHING REGULATOR
-
英文版
3.5A SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
5A SWITCHING REGULATOR
-
英文版
5A SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
1A STEP DOWN SWITCHING REGULATOR
-
英文版
Buck Switching Regulator IC Positive Adjustable 0.5V 1 Outpu...
-
英文版
1A STEP DOWN SWITCHING REGULATOR
STMICROELECTRON...
-
英文版
Voltage-Mode SMPS Controller
ETC
-
英文版
2A STEP DOWN SWITCHING REGULATOR
1
2
3
4
5
6
7
8
9
10
11
