Model Selection Guide
Model
Number
D101EI
D102EI
D103EI
D104EI
D105EI
D106EI
D107EI
D108EI
D111EI
D112EI
D113EI
D114EI
D115EI
D116EI
D117EI
D118EI
D121EI
D122EI
D123EI
D124EI
D125EI
D126EI
D127EI
D128EI
Notes:
Input
Voltage (VDC)
Nominal
Range
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
24
21.6 - 26.4
Output
Load
Fuse Rating
Ef鏗乧iency
Current (mA)
Slow-Blow
Voltage Current
Current Regulation
(%, Typ)
(%, Max)
(mA)
Full-Load No-Load (VDC) (mA, Max) (mA, Min)
256
30
5.0
200.0
20.0
15
78
500
256
30
9.0
111.0
12.0
15
78
500
250
30
12.0
83.0
9.0
15
80
500
247
30
15.0
67.0
7.0
15
81
500
278
30
鹵5.0
鹵100.0
鹵10.0
15
72
500
267
30
鹵9.0
鹵56.0
鹵6.0
15
78
500
247
30
鹵12.0
鹵42.0
鹵5.0
15
81
500
250
30
鹵15.0
鹵33.0
鹵4.0
15
80
500
107
15
5.0
200.0
20.0
15
78
200
104
15
9.0
111.0
12.0
15
80
200
103
15
12.0
83.0
9.0
15
81
200
104
15
15.0
67.0
7.0
15
80
200
114
15
鹵5.0
鹵100.0
鹵10.0
15
75
200
104
15
鹵9.0
鹵56.0
鹵6.0
15
80
200
103
15
鹵12.0
鹵42.0
鹵5.0
15
81
200
105
15
鹵15.0
鹵33.0
鹵4.0
15
79
200
53
8
5.0
200.0
20.0
15
78
100
53
8
9.0
111.0
12.0
15
79
100
53
8
12.0
83.0
9.0
15
79
100
53
8
15.0
67.0
7.0
15
79
100
58
8
鹵5.0
鹵100.0
鹵10.0
15
72
100
55
8
鹵9.0
鹵56.0
鹵6.0
15
78
100
53
8
鹵12.0
鹵42.0
鹵5.0
15
78
100
52
8
鹵15.0
鹵33.0
鹵4.0
15
80
100
1. Output load regulation is speci鏗乪d for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters
will operate without
Output Capacitor
Input
Vin
Vout
external compo-
Capacitor
Single
Dual
nents. However,
5 VDC
4.7
渭F
5 VDC 10.0
渭F
4.7
渭F
when measuring
12 VDC
2.2
渭F
9 VDC 4.7
渭F
2.2
渭F
output ripple, it is
recommended that
24 VDC
1.0
渭F
12 VDC 2.2
渭F
1.0
渭F
an external ceramic
15 VDC 1.0
渭F
0.47
渭F
capacitor be placed
from the +Vout pin to the -Vout pin for single output units and from each
output to common for dual output units. An input capacitor will enhace sta-
bility over temperature and input line variations. Recommended capacitor
values are given in the table above. For applications requiring very low
output noise levels, a simple LC 鏗乴ter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC
output. To do this, connect the load across the positive (+Vout) and nega-
tive (-Vout) outputs and 鏗俹at the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
1
2
5
Single
+Vin
-Vin
-Vout
Dual
+Vin
-Vin
-Vout
Pin
6
7
Single
No Pin
+Vout
Dual
Common
+Vout
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx =
鹵
0.01 (
鹵
0.25)
Pin 1 is marked by a 鈥渄ot鈥?or indentation on the
side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
鈻?/div>
TEL:
(781) 344-8226
鈻?/div>
FAX:
(781) 344-8481
鈻?/div>
E-Mail:
sales@micropowerdirect.com
1
2
