最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

MCP1726-ADJE/MF Datasheet

  • MCP1726-ADJE/MF

  • IC, LDO, 1A, ADJ, 8DFN; Primary Input Voltage:6V; Output Vol...

  • 30頁

  • Microchip   Microchip

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

MCP1726
Once the power good threshold (rising) has been
reached, the C
DELAY
pin charges the external capacitor
to 1.5V (typical, this level can vary between 1.4V and
1.75V across the input voltage range of the part). The
PWRGD output will transition high when the C
DELAY
pin voltage has charged to 0.42V. If the output falls
below the power good threshold limit during the
charging time between 0.0V and 0.42V on the C
DELAY
pin, the C
DELAY
pin voltage will be pulled to ground,
thus resetting the timer. The C
DELAY
pin will be held low
until the output voltage of the LDO has once again risen
above the power good rising threshold. A timing
diagram showing C
DELAY
, PWRGD and V
OUT
is shown
in Figure 4-4.
(turn-on) to the LDO output being in regulation is
typically 100 碌s. See Figure 4-5 for a timing diagram of
the SHDN input.
T
OR
400 ns (typ)
30 碌s
70 碌s
SHDN
V
OUT
V
OUT
V
PWRGD_TH
FIGURE 4-5:
Diagram.
1.5V (typ)
Shutdown Input Timing
T
PG
0V
C
DELAY
C
DELAY
Threshold (0.42V)
4.8
Dropout Voltage and
Undervoltage Lockout
PWRGD
Dropout voltage is defined as the input-to-output
voltage differential at which the output voltage drops
2% below the nominal value that was measured with a
V
R
+ 0.5V differential applied. The MCP1726 LDO has
a very low dropout voltage specification of 220 mV
(typical) at 1A of output current. See the Electrical
Characteristics table for maximum dropout voltage
specifications.
The MCP1726 LDO operates across an input voltage
range of 2.3V to 6.0V and incorporates input Undervolt-
age Lockout (UVLO) circuitry that keeps the LDO
output voltage off until the input voltage reaches a
minimum of 2.18V (typical) on the rising edge of the
input voltage. As the input voltage falls, the LDO output
will remain on until the input voltage level reaches
2.04V (typical).
Since the MCP1726 LDO undervoltage lockout acti-
vates at 2.04V as the input voltage is falling, the drop-
out voltage specification does not apply for output
voltages that are less than 1.9V.
For high-current applications, voltage drops across the
PCB traces must be taken into account. The trace
resistances can cause significant voltage drops
between the input voltage source and the LDO. For
applications with input voltages near 2.3V, these PCB
trace voltage drops can sometimes lower the input volt-
age enough to trigger a shutdown due to undervoltage
lockout.
FIGURE 4-4:
Diagram.
C
DELAY
and PWRGD Timing
4.7
Shutdown Input (SHDN)
The SHDN input is an active-low input signal that turns
the LDO on and off. The SHDN threshold is a percent-
age of the input voltage. The typical value of this
shutdown threshold is 30% of V
IN
, with minimum and
maximum limits over the entire operating temperature
range of 45% and 15%, respectively.
The SHDN input will ignore low-going pulses (pulses
meant to shut down the LDO) that are up to 400 ns in
pulse width. If the shutdown input is pulled low for more
than 400 ns, the LDO will enter Shutdown mode. This
small bit of filtering helps to reject any system noise
spikes on the shutdown input signal.
On the rising edge of the SHDN input, the shutdown cir-
cuitry has a 30 碌s delay before allowing the LDO output
to turn on. This delay helps to reject any false turn-on
signals or noise on the SHDN input signal. After the
30 碌s delay, the LDO output enters its soft-start period
as it rises from 0V to its final regulation value. If the
SHDN input signal is pulled low during the 30 碌s delay
period, the timer will be reset and the delay time will
start over again on the next rising edge of the SHDN
input. The total time from the SHDN input going high
DS21936B-page 16
漏
2005 Microchip Technology Inc.

MCP1726-ADJE/MF 產品屬性

  • Microchip

  • 低壓降 (LDO) 調節器

  • 6 V

  • 0.8 V to 5 V

  • 0.5 V at 1 A

  • 1 A

  • 0.5 %

  • 1

  • Adjustable

  • + 125 C

  • SMD/SMT

  • DFN-8

  • 0.14 mA

  • + 2.3 V

  • 0.05 % / V

  • - 40 C

  • Tube

  • 0.41 V

  • 120

  • 2.5 %

MCP1726-ADJE/MF相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！