最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

MX29F100T Datasheet

  • MX29F100T

  • Macronix International [1M-BIT [128Kx8/64Kx16] CMOS FLASH M...

  • MCNIX

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

MX29F100T/B
DATA PROTECTION
The MX29F100T/B is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power transition.
During power up the device automatically resets the state
machine in the Read mode. In addition, with its control
register architecture, alteration of the memory contents
only occurs after successful completion of specific
command sequences. The device also incorporates
several features to prevent inadvertent write cycles
resulting from VCC power-up and power-down transition
or system noise.
SECTOR PROTECTION WITH 12V SYSTEM
The MX29F100T/B features hardware sector protection.
This feature will disable both program and erase operations
for these sectors protected. To activate this mode, the
programming equipment must force VID on address pin
A9 and control pin OE, (suggest VID = 12V) A6 = VIL and
CE = VIL.(see Table 2) Programming of the protection
circuitry begins on the falling edge of the WE pulse and is
terminated on the rising edge. Please refer to sector
protect algorithm and waveform.
To verify programming of the protection circuitry, the
programming equipment must force VID on address pin
A9 ( with CE and OE at VIL and WE at VIH. When A1=1,
it will produce a logical "1" code at device output Q0 for a
protected sector. Otherwise the device will produce 00H
for the unprotected sector. In this mode, the
address,except for A1, are in "don't care" state. Address
locations with A1 = VIL are reserved to read manufacturer
and device codes.(Read Silicon ID)
It is also possible to determine if the sector is protected in
the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
TEMPORARY SECTOR UNPROTECT
This feature allows temporary unprotection of previously
protected sector to change data in-system. The Temporary
Sector Unprotect mode is activated by setting the RESET
pin to VID(11.5V-12.5V). During this mode, formerly
protected sectors can be programmed or erased as un-
protected sector. Once VID is remove from the RESET
pin, all the previously protected sectors are protected
again.
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 5ns(typical) on CE or WE will not
initiate a write cycle.
CHIP UNPROTECT WITH 12V SYSTEM
The MX29F100T/B also features the chip unprotect mode,
so that all sectors are unprotected after chip unprotect is
completed to incorporate any changes in the code. It is
recommended to protect all sectors before activating chip
unprotect mode.
To activate this mode, the programming equipment must
force VID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.(see
Table 2) Refer to chip unprotect algorithm and waveform
for the chip unprotect algorithm. The unprotection
mechanism begins on the falling edge of the WE pulse
and is terminated on the rising.
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs(Q0-Q7) for an unprotected sector. It
is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
LOGICAL INHIBIT
Writing is inhibite by holding any one of OE = VIL, CE =
VIH or WE = VIH. To initiate a write cycle CE and WE must
be a logical zero while OE is a logical one.
POWER SUPPLY DECOUPLING
In order to reduced power switching effect, each device
should have a 0.1uF ceramic capacitor connected between
its VCC and GND.
P/N:PM0548
REV. 1.2, NOV. 12, 2001
14

MX29F100T PDF文件相關型號

MX29F100TTC-55

MX29F100T相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！