最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

LM20133MHE Datasheet

  • LM20133MHE

  • National Semiconductor [3A, PowerWise㈢ Synchronous Buck Re...

  • NSC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

LM20133
The power stage transfer function is dictated by the modula-
tor, output LC filter, and load; while the feedback transfer
function is set by the feedback resistor ratio, error amp gain,
and external compensation network.
To achieve a -20dB/decade slope, the error amplifier zero,
located at f
Z(EA)
, should positioned to cancel the output filter
pole (f
P(FIL)
). An additional error amp pole, located at f
P2(EA)
,
can be added to cancel the output filter zero at f
Z(FIL)
. Can-
cellation of the output filter zero is recommended if larger
value, non-ceramic output capacitors are used.
Compensation of the LM20133 is achieved by adding an RC
network as shown in
Figure 5
below.
AVIN FILTERING COMPONENTS (C
F
and R
F
)
To prevent high frequency noise spikes from disturbing the
sensitive analog circuitry connected to the AVIN and AGND
pins, a high frequency RC filter is required between PVIN and
AVIN. These components are shown in
Figure 2
as C
F
and
R
F
. The required value for R
F
is 1鈩? C
F
must be used. Rec-
ommended value of C
F
is 1.0 碌F. The filter capacitor, C
F
should be placed as close to the IC as possible with a direct
connection from AVIN to AGND. A good quality X5R or X7R
ceramic capacitor should be used for C
F
.
SUB-REGULATOR BYPASS CAPACITOR (C
VCC
)
The capacitor at the VCC pin provides noise filtering and sta-
bility for the internal sub-regulator. The recommended value
of C
VCC
should be no smaller than 1 碌F and no greater than
10 碌F. The capacitor should be a good quality ceramic X5R
or X7R capacitor. In general, a 1 碌F ceramic capacitor is rec-
ommended for most applications.
SETTING THE START UP TIME (C
SS
)
The addition of a capacitor connected from the SS pin to
ground sets the time at which the output voltage will reach the
final regulated value. Larger values for C
SS
will result in longer
start up times.
Table 3,
shown below provides a list of soft
start capacitors and the corresponding typical start up times.
TABLE 3. Start Up Times for Different Soft-Start
Capacitors
Start Up Time (ms)
1
5
10
15
20
C
SS
(nF)
none
33
68
100
120
30030314
FIGURE 5. Compensation Network for LM20133
A good starting value for C
C1
for most applictions is 4.7 nF.
Once the value of C
C1
is chosen the value of RC should be
calculated using the equation below to cancel the output filter
pole (f
P(FIL)
) as shown in
Figure 4.
A higher crossover frequency can be obtained, usually at the
expense of phase margin, by lowering the value of C
C1
and
recalculating the value of R
C1
. Likewise, increasing C
C1
and
recalculating R
C1
will provide additional phase margin at a
lower crossover frequency. As with any attempt to compen-
sate the LM20133 the stability of the system should be verified
for desired transient droop and settling time.
If the output filter zero, f
Z(FIL)
approaches the crossover fre-
quency (F
C
), an additional capacitor (C
C2
) should be placed
at the COMP pin to ground. This capacitor adds a pole to
cancel the output filter zero assuring the crossover frequency
will occur before the double pole at f
SW
/2 degrades the phase
margin. The output filter zero is set by the output capacitor
value and ESR as shown in the equation below.
If different start up times are needed the equation shown be-
low can be used to calculate the start up time.
If needed, the value for C
C2
should be calculated using the
equation shown below.
As shown above, the start up time is influenced by the value
of the Soft-Start capacitor C
SS
(F) and the 5 碌A(chǔ) Soft-Start pin
current I
SS
(A). that may be found in the electrical character-
istics table.
While the Soft-Start capacitor can be sized to meet many start
up requirements, there are limitations to its size. The Soft-
Start time can never be faster than 1 ms due to the internal
default 1 ms start up time. When the device is enabled there
is an approximate time interval of 50 碌s when the Soft-Start
capacitor will be discharged just prior to the Soft-Start ramp.
If the enable pin is rapidly pulsed or the Soft-Start capacitor
is large there may not be enough time for C
SS
to completely
discharge resulting in start up times less than predicted. To
aid in discharging of Soft-Start capacitor during long disable
periods an external 1 M鈩?resistor from SS/TRK to ground can
be used without greatly affecting the start-up time.
USING PRECISION ENABLE AND POWER GOOD
The precision enable (EN) and power good (PGOOD) pins of
the LM20133 can be used to address many sequencing re-
quirements. The turn-on of the LM20133 can be controlled
with the precision enable pin by using two external resistors
as shown in
Figure 6.
Where R
ESR
is the output capacitor series resistance and
R
C1
is the calculated compensation resistance.
15
www.national.com

LM20133MHE相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！