最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

CS8416-CS Datasheet

  • CS8416-CS

  • Cirrus Logic [192 kHZ DIGITAL AUDIO INTERFACE RECEIVER]

  • CIRRUS

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

CS8416
6 CONTROL PORT DESCRIPTION
AND TIMING
The control port is used to access the registers, al-
lowing the CS8416 to be configured for the desired
operational modes and formats. In addition, Chan-
nel Status and User data may be read through the
control port. The operation of the control port may
be completely asynchronous with respect to the au-
dio sample rates. However, to avoid potential inter-
ference problems, the control port pins should
remain static if no operation is required.
The control port has 2 modes: SPI and I
2
C, with the
CS8416 acting as a slave device in both modes. SPI
mode is selected if there is a high to low transition
on the AD0/CS pin, after the RST pin has been
brought high. I
2
C mode is selected by connecting
the AD0/CS pin to VL+ or DGND, thereby perma-
nently selecting the desired AD0 bit address state.
Figure 11
shows the operation of the control port in
SPI mode. To write to a register, bring CS low. The
first seven bits on CDIN form the chip address and
must be 0010000. The eighth bit is a read/write in-
dicator (R/W), which should be low to write. The
next eight bits form the Memory Address Pointer
(MAP), which is set to the address of the register
that is to be updated. The next eight bits are the data
which will be placed into the register designated by
the MAP. During writes, the CDOUT output stays
in the Hi-Z state. It may be externally pulled high
or low with a 47 K鈩?resistor, if desired.
There is a MAP auto increment capability, enabled
by the INCR bit in the MAP register. If INCR is a
zero, the MAP will stay constant for successive
read or writes. If INCR is set to a 1, the MAP will
auto increment after each byte is read or written, al-
lowing block reads or writes of successive regis-
ters. In the autoincrement mode, the MAP is
incremented in a linear fashion. Allowance must be
made for unused registers.
To read a register, the MAP has to be set to the cor-
rect address by executing a partial write cycle
which finishes (CS high) immediately after the
MAP byte. The MAP auto increment bit (INCR)
may be set or not, as desired. To begin a read, bring
CS low, send out the chip address and set the
6.1
SPI Mode
In SPI mode, CS is the CS8416 chip select signal,
CCLK is the control port bit clock (input into the
CS8416 from the microcontroller), CDIN is the in-
put data line from the microcontroller, CDOUT is
the output data line to the microcontroller. Data is
clocked in on the rising edge of CCLK and out on
the falling edge.
CS
CCLK
C H IP
ADDRESS
C D IN
0010000
R/W
C H IP
ADDRESS
LSB
b y te n
MSB
LSB MSB
LSB
MAP
MSB
DATA
0010000
R/W
b y te 1
High Impedance
CDOUT
MAP = Memory Address Pointer, 8 bits, MSB first
Figure 11. Control Port Timing In SPI Mode
20
DS578PP2

CS8416-CS PDF文件相關型號

CS8416-CZ

CS8416-CS相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！