最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

CS8415A-CS Datasheet

  • CS8415A-CS

  • Cirrus Logic [96 kHz DIGITAL AUDIO INTERFACE RECEIVER]

  • 733.62KB

  • CIRRUS

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

CS8415A
6. CONTROL PORT DESCRIPTION AND
TIMING
The control port is used to access the registers, al-
lowing the CS8415A to be configured for the de-
sired operational modes and formats. In addition,
Channel Status and User data may be read
through the control port. The operation of the con-
trol port may be completely asynchronous with re-
spect to the audio sample rates. However, to avoid
potential interference problems, the control port
pins should remain static if no operation is re-
quired.
The control port has 2 modes: SPI and I
2
C, with the
CS8415A acting as a slave device. SPI mode is
selected if there is a high to low transition on the
AD0/CS pin, after the RST pin has been brought
high. I
2
C mode is selected by connecting the
AD0/CS pin to VL+ or DGND, thereby permanently
selecting the desired AD0 bit address state.
must be 0010000. The eighth bit is a read/write in-
dicator (R/W), which should be low to write. The
next eight bits form the Memory Address Pointer
(MAP), which is set to the address of the register
that is to be updated. The next eight bits are the
data which will be placed into the register designat-
ed by the MAP. During writes, the CDOUT output
stays in the Hi-Z state. It may be externally pulled
high or low with a 47 K鈩?resistor, if desired.
There is a MAP auto increment capability, enabled
by the INCR bit in the MAP register. If INCR is a ze-
ro, the MAP will stay constant for successive read
or writes. If INCR is set to a 1, the MAP will autoin-
crement after each byte is read or written, allowing
block reads or writes of successive registers.
To read a register, the MAP has to be set to the
correct address by executing a partial write cycle
which finishes (CS high) immediately after the
MAP byte. The MAP auto increment bit (INCR)
may be set or not, as desired. To begin a read,
bring CS low, send out the chip address and set
the read/write bit (R/W) high. The next falling edge
of CCLK will clock out the MSB of the addressed
register (CDOUT will leave the high impedance
state). If the MAP auto increment bit is set to 1, the
data for successive registers will appear consecu-
tively.
6.1
SPI Mode
In SPI mode, CS is the CS8415A chip select sig-
nal, CCLK is the control port bit clock (input into the
CS8415A from the microcontroller), CDIN is the in-
put data line from the microcontroller, CDOUT is
the output data line to the microcontroller. Data is
clocked in on the rising edge of CCLK and out on
the falling edge.
Figure 8 shows the operation of the control port in
SPI mode. To write to a register, bring CS low. The
first seven bits on CDIN form the chip address and
CS
6.2
I
2
C Mode
In I
2
C mode, SDA is a bidirectional data line. Data
is clocked into and out of the part by the clock,
CC LK
C H IP
ADDRESS
C D IN
0010000
R/W
C H IP
ADDRESS
LSB
b y te n
MSB
LSB MSB
LSB
MAP
MSB
DATA
0010000
R/W
b y te 1
High Impedance
CDOUT
MAP = Memory Address Pointer, 8 bits, MSB first
Figure 8. Control Port Timing in SPI Mode
17

CS8415A-CS PDF文件相關型號

CS8415A-CZ,CS8415A-IZ

CS8415A-CS 產品屬性

  • Cirrus Logic

  • 音頻 DSP

CS8415A-CS相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！