最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

PIC18F8620 Datasheet

  • PIC18F8620

  • 64/80-Pin High-Performance,256 Kbit to 1 Mbit Enhanced Flash...

  • 380頁

  • Microchip   Microchip

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

PIC18F6520/8520/6620/8620/6720/8720
4.3
Fast Register Stack
4.4
PCL, PCLATH and PCLATU
A 鈥渇ast interrupt return鈥?option is available for interrupts.
A Fast Register Stack is provided for the Status, WREG
and BSR registers and is only one in depth. The stack
is not readable or writable and is loaded with the
current value of the corresponding register when the
processor vectors for an interrupt. The values in the
registers are then loaded back into the working regis-
ters, if the
FAST RETURN
instruction is used to return
from the interrupt.
A low or high priority interrupt source will push values
into the stack registers. If both low and high priority
interrupts are enabled, the stack registers cannot be
used reliably for low priority interrupts. If a high priority
interrupt occurs while servicing a low priority interrupt,
the stack register values stored by the low priority
interrupt will be overwritten.
If high priority interrupts are not disabled during low
priority interrupts, users must save the key registers in
software during a low priority interrupt.
If no interrupts are used, the fast register stack can be
used to restore the Status, WREG and BSR registers at
the end of a subroutine call. To use the fast register
stack for a subroutine call, a
FAST CALL
instruction
must be executed.
Example 4-1 shows a source code example that uses
the fast register stack.
The program counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 21 bits
wide. The low byte is called the PCL register; this reg-
ister is readable and writable. The high byte is called
the PCH register. This register contains the PC<15:8>
bits and is not directly readable or writable; updates to
the PCH register may be performed through the
PCLATH register. The upper byte is called PCU. This
register contains the PC<20:16> bits and is not directly
readable or writable; updates to the PCU register may
be performed through the PCLATU register.
The PC addresses bytes in the program memory. To
prevent the PC from becoming misaligned with word
instructions, the LSB of the PCL is fixed to a value of
鈥?鈥? The PC increments by 2 to address sequential
instructions in the program memory.
The
CALL, RCALL, GOTO
and program branch
instructions write to the program counter directly. For
these instructions, the contents of PCLATH and
PCLATU are not transferred to the program counter.
The contents of PCLATH and PCLATU will be trans-
ferred to the program counter by an operation that
writes PCL. Similarly, the upper two bytes of the
program counter will be transferred to PCLATH and
PCLATU by an operation that reads PCL. This is useful
for computed offsets to the PC (see
Section 4.8.1
鈥淐omputed GOTO鈥?.
EXAMPLE 4-1:
CALL SUB1, FAST
FAST REGISTER STACK
CODE EXAMPLE
;STATUS, WREG, BSR
;SAVED IN FAST REGISTER
;STACK
4.5
Clocking Scheme/Instruction
Cycle
鈥?/div>
鈥?/div>
SUB1
鈥?/div>
鈥?/div>
鈥?/div>
RETURN FAST
;RESTORE VALUES SAVED
;IN FAST REGISTER STACK
The clock input (from OSC1) is internally divided by
four to generate four non-overlapping quadrature
clocks, namely Q1, Q2, Q3 and Q4. Internally, the
program counter (PC) is incremented every Q1, the
instruction is fetched from the program memory and
latched into the instruction register in Q4. The instruc-
tion is decoded and executed during the following Q1
through Q4. The clocks and instruction execution flow
are shown in Figure 4-4.
FIGURE 4-4:
CLOCK/INSTRUCTION CYCLE
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
OSC1
Q1
Q2
Q3
Q4
PC
OSC2/CLKO
(RC mode)
PC+2
PC+4
Internal
Phase
Clock
PC
Execute INST (PC-2)
Fetch INST (PC)
Execute INST (PC)
Fetch INST (PC+2)
Execute INST (PC+2)
Fetch INST (PC+4)
DS39609B-page 44
錚?/div>
2004 Microchip Technology Inc.

PIC18F8620相關型號PDF文件下載

  • 型號
    版本
    描述
    廠商
    下載
  • 英文版
    8-Pin FLASH-Based 8-Bit CMOS Microcontrollers
    MICROCHIP
  • 英文版
    8-Pin, 8-Bit CMOS Microcontroller with EEPROM Data Memory
    MICROCHIP ...
  • 英文版
    8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEP...
    MICROCHIP ...
  • 英文版
    8-Pin, 8-Bit CMOS Microcontrollers
    MICROCHIP ...
  • 英文版
    EPROM Memory Programming Specification
    MICROCHIP ...
  • 英文版
    8-Pin FLASH-Based 8-Bit CMOS Microcontrollers
    MICROCHIP ...
  • 英文版
    Microcontroller
    MICROCHIP
  • 英文版
    Microcontroller 
    Microchip
  • 英文版
    Microcontroller
    ETC
  • 英文版
    EPROM-Based 8-Bit CMOS Microcontroller
    MICROCHIP
  • 英文版
    8-Pin, 8-Bit CMOS Microcontrollers
    MICROCHIP
  • 英文版
    8-Pin, 8-Bit CMOS Microcontrollers
    MICROCHIP ...
  • 英文版
    ETC
  • 英文版
    EPROM Memory Programming Specification
    MICROCHIP
  • 英文版
    EPROM Memory Programming Specification
    MICROCHIP ...
  • 英文版
    28-Pin Programmable Mixed Signal Controller
    Microchip
  • 英文版
    EPROM Memory Programming Specification
    Microchip
  • 英文版
    Microcontroller
    ETC
  • 英文版
    Microcontroller
    ETC
  • 英文版
    EPROM/ROM-Based 8-Bit CMOS Microcontroller Series
    MICROCHIP

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！