最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

CS8406 Datasheet

  • CS8406

  • 192 kHz Digital Audio Interface Transmitter

  • 904.00KB

  • 40頁

  • CIRRUS

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

CS8406
6. CONTROL PORT DESCRIPTION
The control port is used to access the registers, allowing the CS8406 to be configured for the
desired operational modes and formats. The operation of the control port may be completely
asynchronous with respect to the audio sample rates. However, to avoid potential interference
problems, the control port pins should remain static if no operation is required.
The control port has 2 modes: SPI and I虜C, with the CS8406 acting as a slave device. SPI mode
is selected if there is a high to low transition on the AD0/CS pin, after the RST pin has been
brought high. I虜C mode is selected by connecting the AD0/CS pin through a resistor to VL or
GND, thereby permanently selecting the desired AD0 bit address state.
6.1. SPI Mode
In SPI mode, CS is the CS8406 chip select signal, CCLK is the control port bit clock (input into
the CS8406 from the microcontroller), CDIN is the input data line from the microcontroller, CD-
OUT is the output data line to the microcontroller. Data is clocked in on the rising edge of CCLK
and out on the falling edge.
Figure 9 shows the operation of the control port in SPI mode. To write to a register, bring CS low.
The first seven bits on CDIN form the chip address and must be 0010000. The eighth bit is a
read/write indicator (R/W), which should be low to write. The next eight bits form the Memory Ad-
dress Pointer (MAP), which is set to the address of the register that is to be updated. The next
eight bits are the data which will be placed into the register designated by the MAP. During writes,
the CDOUT output stays in the Hi-Z state. It may be externally pulled high or low with a 47 k
鈩?/div>
resistor, if desired.
There is a MAP auto increment capability, enabled by the INCR bit in the MAP register. If INCR
is a zero, the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP
will autoincrement after each byte is read or written, allowing block reads or writes of successive
registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle
which finishes (CS high) immediately after the MAP byte. The MAP auto increment bit (INCR)
may be set or not, as desired. To begin a read, bring CS low, send out the chip address and set
CS
CCLK
C H IP
ADDRESS
C D IN
C H IP
AD D R ESS
LSB
b y te n
MSB
LSB MSB
LSB
MAP
R/W
MSB
DATA
0010000
0010000
R/W
b y te 1
High Impedance
CDOUT
MAP = Memory Address Pointer, 8 bits, MSB first
Figure 9. Control Port Timing in SPI Mode
DS580F1
19

CS8406相關型號PDF文件下載

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！