最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

ST72321AR6 Datasheet

  • ST72321AR6

  • 8-BIT MCU WITH NESTED INTERRUPTS, FLASH,10-BIT ADC, FIVE TIM...

  • STMicroelectronics   STMicroelectronics

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

ST72321
16-BIT TIMER
(Cont鈥檇)
10.4.3.5 One Pulse Mode
One Pulse mode enables the generation of a
pulse when an external event occurs. This mode is
selected via the OPM bit in the CR2 register.
The one pulse mode uses the Input Capture1
function and the Output Compare1 function.
Procedure:
To use one pulse mode:
1. Load the OC1R register with the value corre-
sponding to the length of the pulse (see the for-
mula in the opposite column).
2. Select the following in the CR1 register:
鈥?Using the OLVL1 bit, select the level to be ap-
plied to the OCMP1 pin after the pulse.
鈥?Using the OLVL2 bit, select the level to be ap-
plied to the OCMP1 pin during the pulse.
鈥?Select the edge of the active transition on the
ICAP1 pin with the IEDG1 bit (the ICAP1 pin
must be configured as floating input).
3. Select the following in the CR2 register:
鈥?Set the OC1E bit, the OCMP1 pin is then ded-
icated to the Output Compare 1 function.
鈥?Set the OPM bit.
鈥?Select the timer clock CC[1:0] (see
Table 16
Clock Control Bits).
Clearing the Input Capture interrupt request (i.e.
clearing the ICFi bit) is done in two steps:
1. Reading the SR register while the ICFi bit is set.
2. An access (read or write) to the ICiLR register.
The OC1R register value required for a specific
timing application can be calculated using the fol-
lowing formula:
t
*
f
CPU
-5
OCiR Value =
PRESC
Where:
t
= Pulse period (in seconds)
f
CPU
= CPU clock frequency (in hertz)
PRESC
= Timer prescaler factor (2, 4 or 8 depend-
ing on the CC[1:0] bits, see
Table 16
Clock Control Bits)
If the timer clock is an external clock the formula is:
OCiR =
t
*
f
EXT
-5
Where:
t
= Pulse period (in seconds)
f
EXT
= External timer clock frequency (in hertz)
When the value of the counter is equal to the value
of the contents of the OC1R register, the OLVL1
bit is output on the OCMP1 pin, (See
Figure 51).
Notes:
1. The OCF1 bit cannot be set by hardware in one
pulse mode but the OCF2 bit can generate an
Output Compare interrupt.
2. When the Pulse Width Modulation (PWM) and
One Pulse Mode (OPM) bits are both set, the
PWM mode is the only active one.
3. If OLVL1=OLVL2 a continuous signal will be
seen on the OCMP1 pin.
4. The ICAP1 pin can not be used to perform input
capture. The ICAP2 pin can be used to perform
input capture (ICF2 can be set and IC2R can be
loaded) but the user must take care that the
counter is reset each time a valid edge occurs
on the ICAP1 pin and ICF1 can also generates
interrupt if ICIE is set.
5. When one pulse mode is used OC1R is dedi-
cated to this mode. Nevertheless OC2R and
OCF2 can be used to indicate a period of time
has been elapsed but cannot generate an out-
put waveform because the level OLVL2 is dedi-
cated to the one pulse mode.
One pulse mode cycle
When
event occurs
on ICAP1
ICR1 = Counter
OCMP1 = OLVL2
Counter is reset
to FFFCh
ICF1 bit is set
When
Counter
= OC1R
OCMP1 = OLVL1
Then, on a valid event on the ICAP1 pin, the coun-
ter is initialized to FFFCh and OLVL2 bit is loaded
on the OCMP1 pin, the ICF1 bit is set and the val-
ue FFFDh is loaded in the IC1R register.
Because the ICF1 bit is set when an active edge
occurs, an interrupt can be generated if the ICIE
bit is set.
78/185

ST72321AR6 PDF文件相關型號

ST72321AR7,ST72321AR9,ST72321M7,ST72321M9,ST72321R6,ST72321R7,ST72321R9,ST72F321AR6,ST72F321AR7,ST72F321AR9,ST72F321M7,ST72F321M9,ST72F321R6,ST72F321R7,ST72F321R9

ST72321AR6相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！