最新免费av在线观看,亚洲综合一区成人在线,中文字幕精品无码一区二区三区,中文人妻av高清一区二区,中文字幕乱偷无码av先锋

SC28L194 Datasheet

  • SC28L194

  • Quad UART for 3.3V and 5V supply

  • Philips

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

Philips Semiconductors
Preliminary specification
Quad UART for 3.3V and 5V supply voltage
SC28L194
00110
00111
01000
01001
01010
01011
01100
01101
01111
10000
10001
10010
10011
Start break. Forces the TxD output low (spacing). If the
transmitter is empty, the start of the break condition will be
delayed up to two bit times. If the transmitter is active, the
break begins when transmission of the current character
is completed. If there are characters in the TxFIFO, the
start of break is delayed until those characters, or any
others loaded after it have been transmitted (TxEMT must
be true before break begins). The transmitter must be
enabled to start a break.
Stop break. The TxD line will go high (marking) within two
bit times. TxD will remain high for one bit time before the
next character, if any, is transmitted.
Assert RTSN. Causes the RTSN output to be asserted
(low).
Negate RTSN. Causes the RTSN output to be negated
(high).
Note: The two commands above actually reset and
set, respectively, the I/O2 or I/O1 pin associated with
the I/OPIOR register.
Reserved.
Reserved.
Reserved.
Block error status mode. Upon reset of the device or an
individual receiver, the block mode of receiver error status
accumulates as each character moves to the bottom of
the RxFIFO, the position from which it will be read. In this
mode of operation, the RxFIFO may contain a character
with non-zero error status for some time. The status will
not reflect the error character鈥檚 presence until it is ready to
be popped from the RxFIFO. Command 01101 allows the
error status to be updated as each character is
pushed
into the RxFIFO. This allows the earliest detection of a
problem character, but complicates the determination of
exactly which character is causing the error. This mode of
block error accumulation may be exited only by resetting
the chip or the individual receiver.
Reserved.
Transmit an Xon Character
Transmit an Xoff Character
Reserved for channels b-d, for channel a: enables a Gang
Write of Xon Character Registers. After this command is
issued, a write to the channel A Xon Character Register
will result in a write to
all
channel鈥檚 Xon character
registers. This command provides a mechanism to
initialize all the Xon Character registers with one write. A
write to channel A Xon Character Register returns the
Quad UART to the individual Xon write mode.
Reserved for channels b-d, for channel a: enables Gang
Write of Xoff Character Registers. After this command is
issued, a write to the channel A Xoff Character Register
will result in a write to
all
channel鈥檚 Xoff character
registers. This command provides a mechanism to
initialize all the Xoff Character registers with one write. A
write to channel A Xoff Character Register returns the
Quad UART to the individual Xoff write mode.
Note: Gang writing of Xon/Xoff Character Commands: Issuing
command causes the next write to Xon/Xoff Character Register
A to effect a simultaneous write into the other 3 Xon/Xoff
character registers. After the Xon/Xoff Character Register A is
written, the 28L194 returns to individual write mode for the
Xon/Xoff Character Registers. Other intervening reads and
writes are ignored. The device resets to individual write mode.
10100
Reserved for channels b-d, for channel a: executes a
Gang Load of Xon Character Registers. Executing this
command causes a write of the value x鈥?1 to
all
channel鈥檚
Xon character registers. This command provides a
mechanism to initialize all the Xon Character registers to a
default value with one write. Execution of this command is
immediate and does not effect the timing of subsequent
host I/O operations.
10101
Reserved for channels b-d, for channel a: executes a
Gang Load of Xoff Character Registers. Executing this
command causes a write of the value x鈥?3 to
all
channel鈥檚
Xoff character registers. This command provides a
mechanism to initialize all the Xoff Character registers to a
default value with one write. Execution of this command is
immediate and does not effect the timing of subsequent
host I/O operations.
10110
Xoff resume command (CRXoffre; not active in
鈥淎uto-Transmit Mode鈥?. A command to cancel a previous
Host Xoff command. Upon receipt, the channel鈥檚
transmitter will transfer a character, if any, from the
TxFIFO and begin transmission.
10111
Host Xoff command (CRXoff). This command allows tight
host CPU control of the flow control of the channel
transmitter. When interrupted for receipt of an Xoff
character by the receiver, the host may stop transmission
of further characters by the channel transmitter by issuing
the Host Xoff command. Any character that has been
transferred to the TxD shift register will complete its
transmission, including the stop bit.
11000
Cancel Host transmit flow control command. Issuing this
command will cancel a previous transmit command if the
flow control character is not yet loaded into the TxD Shift
Register. If there is no character waiting for transmission
or if its transmission has already begun, then this
command has no effect.
11001-11011
Reserved.
11011
Reset Address Recognition Status. This command clears
the interrupt status that was set when an address
character was recognized by a disabled receiver
operating in the special mode.
11100-11101
Reserved.
11110
Resets all UART channel registers. This command
provides a means to zero all the UART channels that are
not reset to x鈥?0 by a reset command or a hardware reset.
11111
Reserved for channels b-d, for channel a: executes a chip
wide reset. Executing this command in channel a is
equivalent to a hardware reset with the RESETN pin.
Executing command register reset in channel b-d, has no
effect.
1998 Sep 21
21

SC28L194相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！